iot物聯網選購指南

物聯網開發套件有 win10 ioT、UniPi、e-health、GrovePi 等等，在這裡會不斷的推薦

Microsoft IoT Pack for Raspberry Pi 2 賣場

套件明細：

Raspberry Pi 2 Model B
Adafruit Raspberry Pi B+ Case – Smoke Base / Clear Top –
Full Size Breadboard
Premium Male/Male Jumper Wires – 20 x 6″ (150mm)
Premium Female/Male ‘Extension’ Jumper Wires – 20×6″
Miniature WiFi Module – Official Raspberry Pi Edition
5V 2A Switching Power Supply w/ 6′ MicroUSB Cable
Assembled Adafruit BMP280 Temperature & Humidity sensor
Assembled TCS34725 RGB Color Sensor
MCP3008 – 8 Channel 10-Bit ADC With SPI Interface
Ethernet Cable – 5 foot long
8GB class 10 SD/MicroSD Memory Card w/ Windows 10 -IOT This SD card comes pre-loaded with all the Windows 10 goodies you can handle

電子零件Electronic components

1x Photo Cell
2x Breadboard Trim Potentiometer
5x 10K 5% 1/4W Resistor
5x 560 ohm 5% 1/4W Resistor
1x Diffused 10mm Blue LED
1x Electrolytic Capacitor – 1.0uF
1x Diffused 10mm Red LED
1x Diffused 10mm Green LED
3x 12mm Tactile Switches

GrovePi 賣場

套件明細：

GrovePi Board
GrovePi+ Quick Start Guide
Plastic Storage Box
Grove – Sound Sensor
Grove – Temperature and Humidity
Grove – Light Sensors
Grove – Relay
Grove – Button
Grove – Ultrasonic Ranger
Grove – Rotary Angle Sensor
Grove – LCD RGB Backlight
Grove – Buzzer
Grove – Red LED
Grove – Blue LED
Grove – Green LED
Sensor Cables

零配件館

物聯網網路 Mesh Xbee 賣場底座賣場

XBee Module-Series 1-1mW with Wire Antenna

This is our most popular XBee wireless module: the series 1 802.15.4 protocol 1mW with wire antenna.

The pins on an XBee are 2mm spacing, not 0.1″ so they will not fit into a breadboard. For that reason, they work best in our XBee adapter module kit (which has a 250mA 3.3V regulator) or with the USB XBee adapter.

This module comes with a wire antenna, its the same price as a chip antenna but 50% more range because of the improved antenna, awesome!

XBee Adapter kit v1.1

Onboard 3.3V regulator to cleanly power your XBee, up to 250mA

Level shifting circuitry means that its trivial to connect it to 5V circuitry such as an Arduino without risk of damage

Two LEDs, one for activity (RSSI), the other for power (Associate)

10-pin 2mm sockets included to protect the modem and allow easy swapping, upgrading or recycling

All the commonly used pins are brought out along the edge, making it easy to breadboard or wire up

Specifically created for use with an FTDI cable to connect to a computer via USB. This means that you can use or upgrade the adapter with a computer simply by plugging in a cable

Works with XBee series 1 and 2 as well as Series 1&2 Pro modules

迷你氣象站賣場

Outdoor temperature range: -40.0°C to + 65.0°C
Indoor temperature range: 0°C to + 50.0°C
Humidity range: 10% to 99% (1% resolution)
Rain volume display: 0 – 9999mm (show OFL if outside range)
- Resolution : 0.3mm (if rain volume < 1000mm)
- 1mm (if rain volume > 1000mm)
Wind speed: 0~100mph (show OFL if outside range)
Measuring range air pressure: 27.13inHg – 31.89inHg
- Resolution : 0.01inHg
Alarm duration : 120 sec
Transmission range up to 100m (330 feet)
Power consumption:
- Receiver: 3 x AA alkaline batteries (not included)
- Sensor WH7: 2 x AA alkaline batteries (not included)
Transmission frequency: 433MHz

參考資料：

http://pythonhosted.org/pywws/en/html/index.html

http://www.instructables.com/id/Complete-DIY-Raspberry-Pi-Weather-Station-with-Sof/?ALLSTEPS

http://weather.dragontail.co.uk/index.php?page=station_setup

http://blog.retep.org/2012/07/30/installing-a-usb-weather-station-on-a-raspberry-pi-part-1/

e-Health Sensor Platform Kit V2.0 賣場